This well-designed scope mount allows the scope to move vertically along a guided path. The mount is lockable in different positions using two screws.
The mount can be used as low profile or adjusted the to high profile too if your scope objective its too close to your rifle barrel or shroud.
This practical patent helps shooters who enjoy long-range shooting and often run out of adjustment clicks on their turrets.
The mount can also come handy if you have not been able to use your favorite scope due to lack of space between the rings or unusual position of your dovetail or picatinny rail on your gun.
We are very proud of this product as it has become a “must have” solution among people who love their bullpups.
The design of the mount is dedicated to people who want to improve their performance contrasting with what ordinary mounts allow to do. By keeping the front mount at its lowest and elevating the rear mount to the highest point, you can zero in your gun far beyond what standard mounts allow you to do, without using the clicks on your turrets, hence keeping the optical centre of your scope intact (ideal situation for long range shooting).
Please note: DO NOT use more than 4x elevation screws as you may damage your mount.
Height: 65 mm to 69.5 mm (adjustable)
Profil Height: 21 mm
Adjustable Height: 4.5 mm
Weight: 92 gm each one
Centre of the ring to the bottom of the rail: 38 mm in closed position
Centre of the ring to the bottom of the rail: 42.5 mm in opened position
Ring size: 34 mm
Rail size: 22 mm picatinny
- 1x Infinity scope mount
- 3x Allen key set – different sizes
- 4x Small spare screws
- 6x Large screws
- 1x Waterproof case
- 1x Lens air pump dust blower
Mounting Adapter: converting 20mm Picatinny to 11mm dovetail
Ring adapter: converting 30mm ring to 25mm ring
Accessory top ring with Picatinny rail on top of each ring (useful for mounting a torch)
Bubble levels (Yellow/Clear/Blue/Black/Red/Orange/Green)
Extra picatinny bracket which can be added to the side of the mount (4 can be added easily)
By adding a 11mm X 80mm to Picatinny adaptor you will be able to use the mount on Picatinny or dovetail rifle rail.
You have 2 way to use this adaptor to your rifle:
1: by tightening a few screws on the side – the adaptor will stay on your rifle
can be locked with 2 x grab screws from top will stay tight and secure.
2: take the side screws off place the adaptor to your scope mount rail
then when tightening the scope mount rail will be squeezed and grab the rifle rail.
JAMES CLARKE (verified owner) –
Well made very happy with these scope mounts
skystrut (verified owner) –
I bought this to replace a SPUHR 1 piece mount, my issue was the scope. A RITON X7 4-32 x 56 mm objective 34 mm tube. It was too long to fit between the turretts of the SPUHR So needed a solution, I use this mount/scope on my Ruger American .22 WMR Rimfire rifle, which works great, I used an inch pound torque wrench to fit the mount/scope , and am happy with the results, I am considering a second for my FX IMPACT M3 .25 FAC Air rifle, I would recommend this mount ,because of its flexibility, in adjusting the scope position to get the correct eye relief by using the sliding rail to move the scope forward or rearward to get the perfect position, the extra height is also a great feature especially being able to increase range , especially with an air rifle accounting for pellet/ slug drop. Great bit of kit, sturdy, will buy again.
ioansalter (verified owner) –
Perfect for my M3 with Sidewinder scope
Mark Lawrence (verified owner) –
These are easily the best mounts I’ve ever purchased. The quality and adjustability is fantastic. A free bubble level and mount case seals the deal. I won’t buy any other mounts now.
Raptor (verified owner) –
Purchased two of these, as per the usual high quality by Masood and his team. Fantastic bit of kit enabling me to swap scopes vs Pard across two rifles. Also have the NV008S Eaglevision adjustable mount from a previous purchase, wouldn’t buy anything other than Eaglevision and ‘Made in England’ 😃